Ledger bolts

Get free shipping on qualified Simpson Strong-Tie LedgerLOK Screws or Buy Online Pick Up in Store today in the Hardware department. The most common method is to install ½” lag bolts with washers or carriage bolts with washers. Never counter sink bolts. This will significantly weaken the ledger board. LedgerLOK is a code-compliant structural wood screw engineered to fasten a deck ledger board to the rim joist of a house with no predrilling.

For instance: The bolts and lags must be hot dipped galvanized or stainless steel. Lag screw tips must penetrate the house rim joist – that’s at least ½ in. Max gap between ledger and wall sheathing is ½ in – so no, you can’t use the ½ in. Bolts and screws must be. Structural Screws for Ledgers By Glenn Mathewson Q: For installing a deck ledger , structural screws such as LedgerLoks (which don’t require pre-drilling) are so much easier to use than the lag screws and through- bolts referenced in the IRC.

How to install a ledger board for a deck? What are the best screws for MDF? The ledger basically hangs on the top bolts , but sits atop the bottom bolts , so more space is allowwed. The first bolt goes in from the end at least inches and not more than five. For example, on a deck with a joist span of feet, the lag screws are spaced inches apart.

Product Overview LedgerLOK is the first wood screw engineered to fasten a deck ledger board to the rim joist of a house with no predrilling. The built-in washer head eliminates the need for an additional washer, saving time and money. The large hex-head allows for greater bit engagement, reducing cam-out. Because a ledger board is very heavy and hard to work with, you need to drive framing nails (penny) or screws every two feet to temporarily attach the ledger.

In our example, one of the ledger boards extends past the house. Rows of screws shall be vertically offset and evenly staggered. FastenMaster FMLL005B-2LedgerLOK Ledger Board Fastener , Inches, 250-Count. Ledger Screws are wood screws engineered to fasten a deck ledger board to the rim joist of a house with no pre-drilling. Ledger screws are code tested as deck ledger board fasteners that replaces lag screws and through- bolts.

Learn the pros, cons, and proper placement of ledger bolts , lags, and structural screws. Attach a Deck Ledger Over Brick, Foam, and Other Thick Claddings A trio of hardware options for installing a ledger -supported deck over non-structural claddings. LedgerLOK Flat Head Structural Wood Screw LedgerLOK Fasteners are designed specifically for attaching a deck ledger to the house. This is typically done using carriage bolts, pictured above. When through-bolts are use you’ll either see the head of the bolt or the end of the bolt at the ledger.

Lag bolts work in a similar manner. All structural sheathing materials installed between the deck ledger board and the rim joist shall be positively attached with nails, screws or staples capable of transferring ledger board forces to the rim joists. This configuration requires access from the basement between the floor joists in order to install the washers and nuts. Nuts and bolts are used together.

Toggle bolts are a popular choice for hanging objects on hollow walls like drywall. Replaces ½” lag bolts. Sharp point for fast starts and no pre-drilling, and flathead for flush finishes. LedgerTite screws are designed to fasten ledger board directly to the rim joist of a house without pre-drilling and without the need for a washer. The proprietary coating prevents corrosion, and is recommended for use with ACQ and other forms of treated lumber.

Christopher DeBlois, P. Palmer Engineering in Chamblee, Ga. Whenever there is a design alternative, I generally recommend against bolting a deck ledger board to brick veneer. I prefer to provide independent support adjacent to the house, usually with posts and beams. This connection is critical, since a failure here can cause a deck to collapse.

Failure of the ledger can be caused by too few or undersized fasteners, or by decay in the ledger or band joist. Lags or bolts provide little support when fastened to rotted wood. So proper flashing of the ledger and band joist area is critical. Step – Attach the Ledger Board to the Wall.

Put the ledger board in place once more. Place washers over the holes and screw in the 5. The washers will provide protection for the board from the screw heads. Tighten all the screws in place. There is a separate check for failure mode in the masonry.

Their patented thread technology provides unmatched versatility, drive performance, and requires no pre-drilling – so you can get professional faster, easier, and more efficiently than ever.