How to hide speaker wires for surround sound

Can be painted to sneak invisibly along almost any flat surface. Lengths from - 1ft. How to hide speaker wire with hardwood floors? How do you hide speaker wires?

Poor wire management is always an issue and a cause of many problems down the road after the system is installed. You can get under-carpet wire that is special and flat. Or run the wire through the wall or ceiling. Drop-tile ceilings are helpful to have. If you can find a carpet kicker for rent, you can pull up the carpet to run the wires under, then put the carpet back down, pulling it to the edge with the kicker.

Hide your speaker wire by installing cable raceways. Raceways are long PVC conduits that are just wide enough to. Tuck the speaker wire under your baseboards. If you have a carpeted room, it is easy to hide your speaker wires.

Run the speaker wires above your ceiling. Finish ‘em with a coat of paint and you’re good to go. They are basically lengthy PVC tubes which are sufficiently wide to hold a number of cables.

You can open or close the cable raceways with ease along the lengths of the tubes. One of the more simple methods is to run the speaker wires along the bottom of your walls. Choose a shield or a cord cover close to the color of the hardwood floor , or you can purchase adhesive covers that better match the color of your floor. Overlap inches of four-conductor flat speaker wire with the exposed end of the fish tape and wrap the junction with electrical tape, making the junction as unobtrusive as possible.

Running Surround Sound Wires via Baseboards and Baseboard Moulding This really is the simplest way for running wires for surround sound speakers if you have a carpeted room, and you can get from one location to another without encountering a non-thresholded doorway. Even then there are options. Carpets are laid down through the use of tack strips. To be safe, always route speaker wires along safe paths, like walls and ceilings.

Use secure hooks, ties and cable management systems to keep wiring out of the way, and ensure that passive stresses, like the weight of the wire itself, don’t pull at connector terminals on amps and speakers. Free 2-day Shipping On Millions of Items. Connect any devices you might have. Our shipping policy. Install Cable Ducts.

Make Your Room Net and Clean- Hide Speaker Wire 1. Roll up the speaker wires beneath the carpet and baseboards. If the room where you want to set up the speaker system. Use an awl to punch a hole in the ceiling so you can run the speaker wires.

Note: You will need attic access to the space above the room to hide the speaker wires in the ceiling. Make the hole just large enough for the speaker wire. Then cut a piece of basic speaker wire to the desired length. Strip the jacket of the speaker wire back ¼ inch.

Now insert the ¼ inch bare conductors into the two holes on the ghost wire terminal block and tighten them securely into place. Wipe down the area where you intend to run the wire with a damp cloth. The most common way to hide standard speaker cables is to route them along the baseboard using cord channeling. Cord channeling is made of durable PVC and comes in 5-foot ( meter) lengths.

Channeling is available in two types: flat channeling and round or tunnel channeling. Both types feature heavy-duty adhesive backing. There are also premade wire channels you can buy to hide the wires that can be painted to match existing walls and trim. LimoSales Hide Wires. Hide Computer Cords Hide Electrical Cords Hide Cable Cords Hiding Cords Hiding Tv Cords On Wall Hide Cable Box Organizing Wires Cord Organization Organize Cords.

You can usually hide speaker wire under the baseboard mouldings you may have running around the perimeter of your home theater or living room. Measure enough wire to run around the room from your receiver to where you want to connect your speakers, making sure to leave a few extra feet for clearance (so you can pull your receiver out to adjust your wiring without yanking the wire out of its new home). Outdoors too: hide the speakers under decks.

Frequently used in galleries and museums. Providing multi-zone sound from underneath the floor of a gallery, or sound enabling display cases or the artworks themselves. And countless other environments. Go get an old metal coat hanger, straighten it out and stick into this hole.

Go up in the attic or down in the basement and look for your coat hangers.