How to run speaker wire through walls and ceilings

What is the best speaker cable? You can get under-carpet wire that is special and flat. Or run the wire through the wall or ceiling. Drop-tile ceilings are helpful to have. Buy some electronic connector caps the correct size of the hole (or modefy the hole to fit).

Then you will hot glue your speaker wire to the inside of. The Sonos system is proprietary and will not work with other speaker systems only other sonos systems also it is wireless and you do not need to place the speakers or wires in the wall. If you need to go through an air duct be sure the the wire is Plenum or CMP rated. Speaker wire should be gauge, stranded and conductor with one red and one black wire.

Do not use your cruddy radio shack copper and aluminum wire , this is not meant for in-wall use. Running electrical wires allows you to add additional outlets or switches where needed. Use a fish tape to get two pairs of speaker wire run from the low voltage box up the wall and out the 1-inch access hole.

Route both pairs of speaker wire around the room, securing it to the top of the furring strips. Run wire through hole. Feed the wire through the back of the outlet box, insert the box in the wall , and mount it in place. Strip the wires and attach them to the wall jack or run them to the device. Learn how with this video.

For more in depth informatino about running fish wire and cable through walls please. Grab the wire as it emerges from the hole. Steps to Running Speaker Wires Through Walls and Ceilings.

And now for the actual process. We’ll quickly point out that before you start with this wiring process, you must be qualified or at least knowledgeable about the task at hand. When handling electrical wires —or any job related to electricity—you must be extra careful.

How to Snake Wires Through Insulation. I need to fish some speaker wire through my ceiling downstairs to the lower part of the adjacent exterior wall. Cut a 3- by 5-inch.

To compound the problem, the ceiling joists run perpendicular to the direction I need to run the cable. I have a feeling I already know the answer to this, but is there any way other than cutting several holes in the ceiling to drill. Drill destination hole in floor. If you are looking to do surround soun give more detail.

For example, inexpensive cove molding can be run at floor level (bare floors). Sometimes it’s simpler to cut small holes in walls , especially if your stereo receiver will control multiple speakers in multiple rooms. And If you want to keep cabling looking clean and classy, use.

So I need to run power and HDMI from the receiver cabinet to the projector as well as speaker wire from the receiver cabinet to the four corners of the room. QUESTION: My primary concern is how to run the HDMI and power to the projector. To do this, you can simply use a ruler or paint stir stick to force the wire out of sight. Return to the attic or basement, and drill through the wall plate where you want to guide the wire through.

This option is particularly easy to utilize if you have a suspended ceiling or have not installed a drywall ceiling yet. Speaker wire can be easily run through ceiling joists, or it can be suspended in a cable tray, which can be purchased from a hardware store. Fishing wires through the ceiling. How much drywall you need to cut is based on how well you select the wire path. Using a stud finder, determine which way the joists run the ceiling.

Photo 3: Pull the wires through the walls. Poke a reference wire through the ceiling , then in the attic find the wire and measure over to find the center of the wall. Drop a weighted string through the hole. Attach the cables and pull them up into the attic.

First run the wires around the baseboard to the appropriate locations, leaving enough length to get up the wall to the speakers , with a few extra feet of slack. Make sure there is no internal bracing in the wall to keep the wire from dropping (this is where the stud finder is handy). Unattach the drill from the the end of the bit in the attic and tape the speaker wire to the end of the drill bit.

Push the drill bit down to the area where you want the wire to come out of the wall. If the cable is being run laterally to another stud cavity where it will run vertically to the next box location, you will need to repeat the process by drilling another hole in the wall plate to. Sewell Direct offers “Ghost Wire” that’s a spool of AWG speaker wire, about the width and thickness of duct tape.

It has a strong adhesive on one side, so it can be easily run along walls, floors and under carpets. This invisible wire solution is a non-invasive and low-cost alternative to cutting holes in the wall.